palm oil press machine in belgium

palm oil press machine in belgium

1.Palm Fruit Processing Line parts use high quality of imported bearing and oil seal to ensure high efficient driving, stable and low niose operation.
2.Shandong Microwave Machinery Co.,Ltd.Independent research and development of large air shaft without hoop equipment, overtuns the traditional process, make palm oil press machine in belgium more stable and reduce the cost maintenance time of Palm Fruit Processing Lineusers.
3. Add palm oil press machine in belgiumnon-stop refueling system, automatic system for the butter, air cooling system, high efficiency, low energy consumption, smooth operation, the Palm Fruit Processing Line quality is stable and reliable.
4. Shandong Microwave Machinery Co.,Ltd. product with high automation which can save labor, and palm oil press machine in belgium is also easy to maintain which save lots of maintance time.

Specifications

palm oil press machine in belgium

Reception station:

A, The FFB bunch be transported to plant by truck, after be weighted by weighting bridge, the FFB will be loaded down to FFB Loading Ramp.

B, The iron door of unloading ramp is controlled by hydraulic device, Get the power from Hydraulic pump station. Start on the hydraulic device, iron door be lifted. FFB will fall down to the Palm Fruit screw conveyor, be transported to pre-treatment plant, to Vertical sterilizer.

Sterilizing process:

A, By Scraper Conveyor, FFB be transported to the top of sterilizing tank. Falling into sterilizing tank from feed inlet.

B, Sterilizing tank: The inside diameter of sterilizing tank is φ2000mm, length 12500mm, welded up by Q235B material (Chemical composition:C0.12~0.2%,Si0.12~0.3%,Mm0.3~0.7%,P

C, After FFB be transported into sterilizing tank (202), close the door of sterilizing tank, and open the vent valve behind the tank, then saturated steam, which pressure is 3bar and temperature is about 130°C. After all the cooling air have been discharged out,close vent valve, proceed to sterilizing section. Sterilizing time is 55~60minutes.

D, The time of sterilizing is also according the kind of FFB, if the pressure is too high or the time is too long , palm fruit will be rot, also Resulting in the loss of oil, high temperature can change palm color.

E, Finish sterilizing process, close the steam valve, open the valve lead to Blow-off/down Silencer, can’t open the sterilizing tank door until discharges out all steam and water.

F, Open the sterilizing tank door, sterilized FFB will fall on the FFB Scraper conveyor. Be transported to next station.

Threshing station:

A, The sterilized FFB will be transport to thresher platform by scraper conveyor.

B, We adopt advanced Drum type thresher, insider diameter is φ1800mm, length is 5000mm.The material of main shaft is #45 steel (main chemical composition is C0.42~0.50%, Si0.17~0.37%, Mm0.50~0.30%, P≤0.035%, S≤0.035%, Cr≤0.25%, Ni≤0.25%, Cu≤0.025%).

C, Sterilized FFB be twisted and knocked in thresher. Palm fruit will be separated from empty bunch totally, fall on Fruit Scraper conveyor though fence, the empty bunch will be transported to Bunch Temporary tank by Bunch Scraper conveyor.

palm oil presser press:

A, The palm fruit is transported to Crush tank (401) by fruit elevator.

B, The fruit in crush tank will be heated to 90~95°C, crush time is 10~20 minutes.

C, The pounded fruit flow into Palm fruit oil presser(402) to press. Oil press cone can control cylinder, working pressure is 50~70bar, revolving speed of presser main shaft is 12.5 r/min. Meanwhile the mixture of crude palm oil and water outflow from barrel holes. Crude oil will be flow in Temporary Storage oil tank(T06) through crude oil groove. Then oil will be pumped to Screening filter(601) by oil pump. After filtering take out the oil foam, deposit impurities. Palm oil flow into Passivating oil tank(602). The fiber cake and nucleus are eLDausted from clearance of cone head drop on Breaking cake auger (501).

D, Palm fruit oil presser (402), the material of main shaft is 40Cr steel, (Chemical component: C0.37~0.44%,Si0.17~0.37%, Mn0.50~0.80%,Cr0.80~1.10%) have been thermal refining, the material of worm and cone head is 45# Cast-Steel, and the surface have quenching treatment.

Kernel recovery system:

Sewage treatment:

Our Warm Professional Advice:

If you like our products,please kindly tell us your requirements,includes raw material name ,your processing capacity per day, have the production plant or not and related data, then we can efficiently make a cost-effective plan for you, we can calculate the cost and profit for you. Your trust and support are our large success.

Shandong Microwave Machinery Co.,Ltd.is a Palm Fruit Processing Line factory specializing in the production of palm oil press machine in belgium, scientific research,manufacturing,installation, commissioning.Shandong Microwave Machinery Co.,Ltd.can provide Palm Fruit Processing Linecustomers with design and services of 1-2000 tons palm oil press machine in belgium. Shandong Microwave Machinery Co.,Ltd. have finished hundreds of successful projects Palm Fruit Processing Lineover the years: peanut oil, soybean oil, rapeseed oil, cottonseed oil, sunflower oil, seCARRIEe oil, animal oil,grape seed oil, acer truncatum oil, peony seed oil, walnut oil, hemp seed oil, pine oil, tea seed oil, papaya oil, milk thistle seed, and other special type Palm Fruit Processing Lineoil. Shandong Microwave Machinery Co.,Ltd. have independent import and export department. Shandong Microwave Machinery Co.,Ltd. Palm Fruit Processing Lineequipment has been successfully exported to more than ten countries: Russia, Australia, India, Afghanistan, Cameroon,and so on.

Contact us:

Carrie-Sales manager

Shandong Microwave Machinery Co.,Ltd.

Web: www.epier.com

Email: [email protected]

Skype:leaderfoodmachine10

Moblie:0086-15020017267(also WhatsApp)