Company Information:
Our Strength:
1, Established in 1982, we have more than 30 years experience. Our goal is to be pioneer in
global grain and oil
industry.
2, We have deep cooperation with Shandong Machine Design Research Institute and Shandong
University of
TechnoloLD. Our professor often go abroad attending grain and oil conference and forum.
3, We have completed service line including technical department, engineering department,
project department, electronic commerce department, domestic trade department and foreign trade department.
After signing contract, we will set up special team including engineers, installation technicians, drawing
designer, business person, after-sales service person, and so on. We will provide one-to-one service.
Our Service:
1, Whole set of equipment for production line.
2, Motor and power control system.
3, Installation material.
4, Installation and test-run.
5, Drawing of process description, equipment layout, foundation and hole, construction.
6, Drawing of power control.
7, Isolation and painting for equipment.
8, Water recycling and cooling system outside the plant (i.e. supplementary device).
9 Staff training and long-term technical service.
Main Business Field:
1, 10-500T/H oil material primary cleaning,drying and storage section turn-key project.
2, 100-3000 T/D oil pretreatment, shelling and pre-press workshop turnkey project (soybean hot
dehulling, bean skin crushing, the soybean extrusion, high oil contained pre-pressed cake
extrusion and high oil contained flakes puffed directly). Rice bran turn-key project.
3, 100-3000 T/D leaching workshop turnkey project (towline extractor, rotocel extractor, loop
type extractor,
4, DTDC separated machine, the full negative pressure evaporation, Paraffin wax recovery, leaching workshop degumming, phospholipid concentration).
5, 30-1000T/D continuous physical (chemical) refining line.
6, 20-3000T/D sunflower oil, rice bran oil, corn germ oil dewaxing turnkey project.
7, 10-200T/D fatty acid esterification edible oil production line.
8, Some edible oil machine product line.
Available Oil Raw Materials:
Refine
1.What kind of crude vegetable oil can be refine?
Crude soybean oil, palm oil, palm kernel oil, sunflower oil, canola oil(rapeseed oil)
,peanut oil, sesame oil, conttonseeds oil etc. 
2. The flow chart of refining:
Hydration Deguming & Alkali Refining Deacidification
The crude oil is output by the oil feed pump from the oil tank, and next enters the crude
oil heat exchanger to recover part of heat after metering and then is heated to the required
temperature by the heater. After that, the oil is mixed with the metered phosphoric acid or citric acid
from phosphate tank in the gas mixture (M401), and then enters the conditioning tank (R401) to
make the non-hydratable phospholipids in oil change into the hydratable phospholipids.
Add the alkali for neutralization, and the alkali quantity and alkali solution concentration
depend on the quality of the crude oil. Through the heater, the neutralized oil is heated to the
temperature (90℃) suitable for centrifugal separation to remove the phospholipids, FFA and other impurities in
the crude oil. Then the oil goes to the washing process.
Bleaching
In normal situation , there is pigment in the crude oil , we need to using the active clay
to absorb the pigment away , after 20 mins , we use the vibrating filter to filter the waste clay away .
If you want to get ligLD color oil , you need to add more active clay . That is mean , the customer can
accord to his requirement to control the oil color. This process is carried out under the vacuum
condition.
Deodorization
Usually ,there are some odors in the crude oil , it affects the quality of the edible oil .
About our refining process , we usually use the direct steam to take odors away in the vacuum
condition . General speaking there is about 0.5% water in the alkali refined oil, in the deodorization
pot, the temperature is very high , it also can finish the dehydration section.
Filtering
This process can remove off the small amount of unsettle gum soluble impurities in the
degummed oil, after oil dehydrate cooling (60 °C), filtering again, to ensure the product oil
quality. Then pumping the final oil into the oil tank.
3.Main refininf section:
(1) Degumming section: used to P-acid de-gumming, alkali refining de-acid and water rinsing.
(2) Decoloring section: used to remove off pigments, bleaching oils and grease dehydrate.
(3) Deodorizing section: to remove off the odor components in oil.
(4) Dewax: used to remove off the wax in the oil, in order to get the high quality oil.
(5) Heat-transfer oil stove: supply each device production needing heat enerLD, temperature
reach above 280C.
(6) Steam generator: produce the needing steam for de-odoring and distillation.
(7) Vacuum pump: supply needing vacuum for dehydrate, de-color, de-odor. Vacuum degree
can reach above 755mm Hg.
(8) Press filter: filter clay, filter out clear oil.
(9) Air compressor: blow dry bleached clay, blow empty the leftover oil in the press filter.
laboratory
Our Services
1 Engineers to the scene to guide the installation;
2 Online question reply;
3 The warranty period of 12 months;
Our engineers in guiding workers how to operate the machine:
Packaging & Shipping
Contact with me