China manufacturer export all over the world flax seed oil extract machine

China manufacturer export all over the world flax seed oil extract machine

Product introduction

Flax seed oil press machine

LD brand Flax seed oil press machine ,introduce overseas advanced technology,combining grain and machinery experts at home and abroad to develop a new generation of high efficiency and energy saving oil equipment. Conform to the technology requirements and standards of department of agriculture. Original oil processing production, colour and lustre is pure,it is the best choice for modern oil mill. Our Oil machine design science, reasonable structure, convenient operation, safe and stable, with full automatic device, from feeding to the finished product finished only a few minutes at a time. Is made of high carbon steel, after high frequency quenching, heat treatment, high hardness, strength, good abrasion resistance, to adapt to the continuous operation of high temperature and high pressure,which could improve the service life of the soybean oil machine,can be used for decades.

Oil from the oil press equipment squeezed into the oil filter, press the pump button, vacuum pump starts to run, the air inside the filter will be pumped , Oil filter barrels inside will form internal pressure,the above oil will be pumped into the oil filter naturally, Oil residue will be isolated in the filter cloth ,wating for pressing finished,oil be pumped over, open the valve on the oil filter, stop the pump running, dry slag is formed on the filter cloth, with a scraper scrape, can put the pure oil bottom valve which in the oil filter.

Technical advantages

Energy saving----- equal to lower production of electric power 40%,saving an average of 6 kilowatt-hour basis, savings of 30RMB per day production of electricity.

Saving of labor-----the same production can save Labour 60%, 1 to 2 people to organize production.

Widely used------ multi-usage, squeeze peanuts, sesame, rapeseed, soybean, canopy, flax ,more than 20 oil crops. Level 3 press, a squeeze net.

Oily pure----- vacuum filter residue and ensure the pure oil, conform to the health and quarantine standards.

Covers an small area----- oil mill only needs 10 to 20 square meters can satisfy the production need.

The instructions on oil press

(1) Flax seed oil press machine each work 50 hours later check the lubrication situation, reducer oil cup above shall not be short of oil, oil mill squeezer shaft adjustment screw bearings should be adjusted screw hole in each class loaded with butter, dry grinding is forbidden.

(2) Of the Flax seed oil press machine
the lubrication parts should prevent dust and other impurities into, every year to check the oil quality of Flax seed oil press machine
gearbox, found that bad, all the oil should be changed.

(3) When the Flax seed oil press machine
amount is reduced, the bread or the oil is not normal, should take out oil mill squeezer shaft, check the Flax seed oil press machine
squeezer, pressing bar, wear and tear on the circle in cake, wearing parts to change in time. (4) Per class after work, should remove residues in soy oil press cake, the clean oil press surface dust, oil dirties.

(5) The production end of the season after long-term storage, should be a service, and will press squeezer, pressing bar, a cake circle to unpick and wash oil, put in dry place.

Technical parameters

Process characteristics of 3T/D edible oil refining equipment.

Process description:

The whole process of intermittent refining:

Oil inlet→heating up→deacidification→dealkalizing→washing 2-3 times→dry dehydration. The total time is about 24 hours.

According to the difference of alkali thickness and oil temperature, the process of dealkalizing is divided into two types, one is low temperature with thick alkali (its initial temperature is 20 ~ 30 ℃, alkali thickness is 20 ~ 30 Be) and another one is high temperature with light alkali (its initial temperature is 75 ℃, alkali thickness is 10 to 16 Be). The former is generally applied and the latter is mainly used for crude oil which has low acid value, light clour and lustre, and less impurity.

I. Low temperature with thick alkali:

Adjust the oil temperature to 20~30℃, then put in 20~30Be alkali liquor in 5~10 minutes, and stir it about 20~60 minutes on condition of 60r/m. Increasing the temperature slowly when notice the separate of neatsoap after reacted, 1℃ per minute, when it reach 60℃, stop stiring, keep still and make soap feet settlement, it will takes nearly 6~8 hours, then let out the soapstock.

Ⅱ. High temperature light alkali operation:

Firstly,determine the alkali thickness in accordance with the alkali value of crude oil(according to the table below), account the alkali and water added in, when the alkali value is under 5, for each unit acid value, the total water added into per ton oil is 23 kg. When the alkali value is over 5, no more than 12% of the oil heavy, the exceeded alkali is only 0.005~0.002%.

When operating, first mix the crude oil, heat the temperature to be 70 ~ 75 ℃ diluted saline or phosphoric acid (concentration 90%) , when particles appear, add alkali, then continue to stir for 40 ~ 50 minutes and heat up to be 90 ~ 95 ℃ until soap grain obviously separated, and put into nigre after 2 ~ 3 hours' static.

Ⅲ. Washing:

After releasing the nigre, grease heated up to boom 90℃, then add in the hot water for washing, stirring. Water temperature should be about 5 ~ 10 ℃ higher than the oil temperature, for low water temperature tends to emulsification. After adding the water, continue to stir for 5 minutes, then rest 4 hours for precipitation, and release the soap water, wash 2 ~ 3 times depending on the oil quality and decide. Washed oil slowly heated up to 105℃, stirred dehydration for 1 hour, washed oil can also direct inhaled decoloring pot and vacuum drying 30 minutes.

Method of operate for descoloring

1 start the vacuum pump,vacuum degree ≥700mmHg

First, after washing of alkali refining inhaled decoloring pot, stirring, at the same time warming up to 90 ℃, and stir another 30 minutes, decrease moisture below 0.1%, then inhale a few decoloring agents "white earth, activated carbon >, the quantity depends on the oil color, generally, oil amount 2 ~ 4%, stirring 30 minutes, cooled to 70 ℃, use compressed air pressure to filter oil machines to separate the white earth and oil, then get decoloring oil.

Method of operate for deodorizating

l By vacuum pump oil bleaching inhaled deodorization pot, up to 755 mmHg in vacuum degree , begin distillation and deodorization timing;

l Deodorizating time : 4 Hours

l Deodorization temperature: 240℃/755mmHg~260℃/759mmHg

l Deodorization vacuum degree: above 755mmHg

l There is steam distillation during the whole timing process.

l After deodorization, shut off the direct steam in vacuum condition , close conduction oil,open the valve for cooling water.,until the oil temperature nearly 40~80 ℃,shut off the vacuum pump valve,make test of the oil sample,if it is passed inspection,packing and finish all the manufacturing of edible oil.

Characteristics

l Both short mixed and long mixed process are adapted in washing sector, which ensures washing effectiveness.

l Equipped with vertical leaf filter to remove used bentonite from the oil, operating conveniently and continuously, low laboring tense, keeps environment well, keeps oil residence in deposable bleaching earth in low level.

l Due to accurate stirring method, decreased the maximum distance between the oil of cooling facet so as to ensure the same temperature of crystal with same quality. Better guaranteed that in the process of crystallization, crystal will not cluster in a intense area.

l Flexible system, cooling curve can be easily altered by changing water temperature, thus the kinds of products can be changed easily.

The main economic technical parameters:

Caution

when machine product oil normally, soybean oil mill must maintain uniform feeding, not too little or too much or idling. The oil mill load is normal, stable running, sound rhythmically. The cake smoothly coming out, low pressure section almost no slag, high pressure section has a small amount of slag, but not greater than 9% slag in the oil, oil mill press chamber temperature can reach 150-200 °C, the pie mouth emitted smoke should be through the shield by smoking pipe. Hot cake squeezed out should be spread out in time, do not be eager to make heap or shipment, otherwise it will produce spontaneous combustion phenomenon. When work continuously for a long time, oil press with high temperature , electric fan blowing and other cooling measures should be taken.

Pre-sale

System evaluation: 1)Project basic situation

Solution: 1)The investment budget. 2)Feasibility, rationality

Product selection: 1)Factory inspection. 2)Site measurement. 3)Technical discussion. 4)Supply professional drawing and lists.

Win--win coopration: 1)Sign the contract. 2) Establish mutual benefit, strategic cooprative partnership.

In-sale

Design evaluation:1) Detailed technical assessment, arrangement. 2)Design of process and equipment layout.

Procurement: Strictly inspection, optimized selection.

Installation: 1)Quality and quantity guaranteed. 2)Completion of hand over.

Acceptance:1)Acceptance test. 2)Accepted deliverable

Technical training: 1)On-site installation and products training. 2) Operation skills training. 3) Maintenance training. 4) Centralized technical training

After-sale

Technical service: Long time technical service

Accessories supplying: Supplying spare parts with cost price.

Feel free contact me to get more information