New condition oilseeds friction screw press, screw press machine, screw press oil expeller price
LD'e shipping:
Features of the oil press equipment:
1. Stainless steel used on the surface to reach the standard of food hygiene.
2. Cold lower temperature keep in pressing technology.
3. Durable, for 1 year free after-sales service. Include replace the parts costs.
4. A double helix oil press equals two oil press, can obtain double benefit
5. High quality parts, stable oil pressing effect, saving the maintenance cost.
6. Military industrial manufacturing, quality chrome materials, quality trustworthy.
Oil from LD'e press:
Parameters of LD'e press:
| Model | 6YL-80 | 6YL-100 | 6YL-120 | 6YL-130 |
| Screw speed | 30-45r/min | 30-40 r/min | 30-40 r/min | 28-40 r/min |
| gear ratio | 14/42x19/57=1:6.63 | 15/40x15/55=1:9.78 | 15/34x15/55=1:9.59 | 15/38x19/48=1:7.38 |
| Dimension | 1650x1150x1750 | 1950x1300x1900 | 2050x1350x2000 | 2200x1600x2150 |
| Productivity | 80-150kg/h | 150-250kg/h | 200-300kg/h | 250-400kg/h |
| Power | Y160L-6-5.5KW | Y160M-6-7.5KW | Y160L-6-11KW | Y180L-6-15KW |
| Vacuum pump | Y90S-4-0.55KW | Y90S-4-1.1KW | Y100L1-4-1.5KW | Y100L1-4-2.2KW |
| Heater | 2KW | 3KW | 3.3KW | 3.8KW |
Way to operate LD'e press:
1. After installing the machine, check whether lubricant has been filled in, bolts have been tightened, and handles are operable.
2. Check large pulley whether it is loose or blocked, repair it if necessary
3. Adjust the tightness of the belt. LDitch on the motor and check its rotation direction.
4. Loosen the lock nut, rotate the adjusting handle and tighten the screw to its end, then loosen it for 3-4 circles and tighten again for half circle to assure the gap of the residue cake outlet.
5. Feeding must be steady and slow at the beginning to avoid blocking.
6. In case no cake is extruded outward, return back the screw for 1-2 circles. If there is still no cake being observed, machine needs to be shut down and checked. However, in any case, operating the machine backwards is absolutely prohibited. Normally, cake looks like tile but not sticky; thickness is 1-2mm inner side is smooth, outer side creases and no oil on the surface is allowed Cake thickness adjustment:Rotating the adjusting handle clockwise will make the cake thicker, anticlockwise, and thinner. Each circle of adjustment will change the thickness 0.4-0.5mm
7. When machine is operating, oil extruding and residue outlet need to be checked frequently. Normally, most of oil will flow outwards from square rods and several front round plates. Broken cake residue indicates the material is too dry; steam emerging from the cake residue indicates that it is too wet; In any case, water content in the raw material must be adjusted from time to time. Slag ice emerging indicates high water content; powder-like slag, low water content. Loose round plates will cause too much slag flowing outwards. However, adequate water content will not cause slag flowing outwards from square rods. Yet, little slag from round plates is allowed. In a word, water content affects oil output rate, so it needs adjusting properly
8. Stop the machine: Repeatedly move screw forwards and backwards for several times and let all material resided in the chamber go out and adjust the cake to a thickness as thin as possible, then stop the machine. When machine stops by any accident, power supply must be shut down first, then rotate large pulley manually backwards to let the material turn out. Then pull out the shaft and clean it in case the shaft couldn't be pulled out, remove the upper case and loosen lock nut, separate round plates and clean them one by one.
LD'e certificates:
Still have questions?
What should you do??
Do not worry!
Jessica is always here!!
Just Contact Jessica!!!