High efficiency coconut oil mill

Petroleum Refinery can be used in black engine oil, crude oil,Pyrolysis oil and shale oil, to get gasoline and diesel oil through distilled catalyst. Pumping into the heater with raw material , through the gas,fuel oil or coal heating to working temperature, the maximum working temperature of High efficiency coconut oil mill about 410 degree and the required gasoline and diesel oil can be obtained after catalytic distillation. When the reaction of Petroleum Refineryraw material in reactor is complete, stop heating, and remove residue from the tank of bottom, then High efficiency coconut oil mill can be used again.

Shandong Microwave Machinery Co.,Ltd.Petroleum RefineryIndex of oil after treatment:
Petroleum Refinerydiesel oil : 86-88%, gasoline oil: 5-6%,oil residue: 6-8%.
Petroleum RefineryLow-speed diesel engine can be used directly
Petroleum Refineryperformance characteristics,advantage introduction

Specifications

High efficiency coconut oil mill

Our Factory

Main business:

• 10-500T/H oil material first cleaning,drying and storage section turn-key project.
• 100-3000 T/D oil pretreatment, shelling and pre-press workshop turnkey project (soybean hot peeling, bean skin crushing; the soybean extrusion, high oil contained pre-press cake extrusion, and high oil contained embryos puffed; of direct puffed). Rice bran production line turn-key project.
• Leaching workshop turnkey project (Towline extractor, Rotocel extractor, loop type extractor, DTDC separated machine, the full negative pressure evaporation, paraffin wax recovery, leaching workshop degum, phospholipid concentrate).
• 30-1000T/D oil continuous grade two or one physical (chemical) refining production line.
• 10-600T/D sunflower oil, rice bran oil, corn germ oil dewaxing turn-key project
• 10-200T/D Fatty acid esterification production cooking oil production line.

Coconut oil mill machine:

Coconut oil mill operation priciple:

The first step:Open the cap of the oil tank,and fill in the hydraulic oil into it.

The secind step:Open the red switch of Power Distribution Cabinet to preheat the machine.

The third step:One hand hold the handle,then the other one pull the cap of the machine,and

pour the oil material into the charging barrel.

(if the oil material is not so much,we can put them into the special bag,cos the heavy pressure can make the oil material flow through the oil-way,and stop it up).

The fourth step:Put the iron mat onto the oil material and close the cap,and tighten the nut on it .

The fifth step:Turn the high-pressure reflux valve and the machine start to work.At the same time,the oil tank will go up to press the oil material and the oil follow from the oil way by the high pressure.

The sixth step:There will be an oil-out beside the lacquer tray,below it,we can put down the oil can for oil collection.

The seven step:The machine will stop work for a while, when the pressure is under some degree,and after several minutes,the second pressing will begin automatically,ans when the pressure goes to the adjusting degree,the presser will be stoped for the first ending.

The eight step:Stop the the high-pressure reflux valve and let the oil tank go down,loosen the nut and open the cap,then the meal will go up as the oil tank rising up,take the meal out of the machine,and break it manually.

Tips:The second pressing and third pressing are the same as the first one.And there is a temperature-controlled setting on the distribution box,when you open it,the machine can be heated by the infrared ray,and you can choose the ways of pressing,hot or cold by yourselves.

Coconut oil mill need attention:

1.when cooking ,reduce material powder and stirring time,clean cooking pot tremie pipe mouth and elevator discharge pipe regularly,to prevent the material gathered.

The feature of coconut oil cake which produced by a good maintenance and operation screw presser as follow:

1).Light -colored oil 8/50(R/Y measured by lowe friends method)

2).Cake apparent beige,the most residual oil is 8%

3).Unanimous thickness about coconut cake,about 0.6cm and fine powder less than 6%

2. When expelling,adjusting pressing,bar clearance,improve material

After cooking ,feed flow,the oil mainly come out in the second and the third paragraph.

Worthy is that material flow into chamber can not big ,at the beginning of the feed, before the chamber temperature raising up,otherwise,it is form a thin paste in the feed so that cake flow not free and even sintering.

Coconut oil knowledge:

There are 30%-40% oil and 50% water in fresh coconut,while ,there are 60%-70% oil in copra,just 4%-7% water,coconut oil possess sepcial fragrance.

The oil is extracted by crusher or screw persser,it recoveried residual oil from cake with the second extraction as a supplemnt by solvent .

Mechanical extraction process:To transgfer the copra which contain 10%-12% water to automatic balance and magnetic speration to remove junk iron, and grind it to particles that the diameter is about 0.3cm.

Put the embryo in the 115°C horizontal cooker with 20min,under this condition,fat cell crack,phospholipid sedimentation,water containing down to 3%.To transfer the same size embryo after cooked to presser for continuous extraction.Grease discharge with uniform decline curve at the most of time.Generally speaking ,coconut cake residual oil is 7% after processing.

Why choose our coconut oil mill?

Coconut oil mill is of the same products abroad in introducing based on improved design becomes.The mahcine is specialized wrung sesame,wulnuts,almods,wait til raw materials,machinery,simple operation,convenient haracteristicof high.let the squeeze is on customers eat assured oil.

Coconut oil mill terms of payment :

The sum equal to 30% of the total amount of the Contract must be transferred by the buyer to the Seller’s account directly within Five (5) bank working days from the date when the Contract has been both signed as down payment.

The sum equal to 70% of the total amount of the Contract will be transferred by the buyer to the Seller’s account directly after checking and accepting the finished equipment in the seller's factory at five(5) bank working days .The goods are deemed accepted by the buyer after the signing of the"The act of acceptance of the equipment"by the representatives of the seller and the buyer.

Cold pressed virgin coconut oil

Please contact us with best service after sales

Shandong Microwave Machinery Co.,Ltd.is a Petroleum Refinery factory specializing in the production of High efficiency coconut oil mill, scientific research,manufacturing,installation, commissioning.Shandong Microwave Machinery Co.,Ltd.can provide Petroleum Refinerycustomers with design and services of 1-2000 tons High efficiency coconut oil mill. Shandong Microwave Machinery Co.,Ltd. have finished hundreds of successful projects Petroleum Refineryover the years: peanut oil, soybean oil, rapeseed oil, cottonseed oil, sunflower oil, sesame oil, animal oil,grape seed oil, acer truncatum oil, peony seed oil, walnut oil, hemp seed oil, pine oil, tea seed oil, papaya oil, milk thistle seed, and other special type Petroleum Refineryoil. Shandong Microwave Machinery Co.,Ltd. have independent import and export department. Shandong Microwave Machinery Co.,Ltd. Petroleum Refineryequipment has been successfully exported to more than ten countries: Russia, Australia, India, Afghanistan, Cameroon,and so on.

Contact us:

Carrie-Sales manager

Shandong Microwave Machinery Co.,Ltd.

Web: www.epier.com

Email: [email protected]

Skype:leaderfoodmachine10

Moblie:0086-15020017267(also WhatsApp)